6S 30000mAh

Custom Semi-Solid Battery Packs, 280–500 Wh/kg | BECELL

Custom Semi-Solid Battery Packs: Built to Your Current, Size and Weight Requirements

By BECELL Technology | Huizhou, Guangdong, China

If you are sourcing semi-solid batteries, the real constraint is rarely finding a high-Wh/kg cell. Instead, the challenge is finding a pack that fits your continuous and burst current profile, your installation envelope, and your weight budget—without asking your mechanical team to redesign the product around a standard catalog part.

uav-battery-cells-becell

Therefore, BECELL approaches custom battery development from the opposite direction. We start with your electrical and mechanical boundaries, and then we match the semi-solid platform—280 to 500 Wh/kg—to those boundaries.

Have current, size and weight requirements ready? Send them to our engineering team for an initial feasibility review.
[Request a Custom Semi-Solid Battery Quote]

Why “Custom” Matters Before “Spec Sheet”

A 500 Wh/kg platform figure tells you what is possible at the upper end. However, what determines whether a semi-solid pack works in your device is how precisely we match three variables.

Current matching. First, consider your load profile: is it continuous high-rate, short burst, or a combination? The BECELL semi-solid platform supports 3C continuous discharge and 10C burst discharge across most product tiers, and it offers 0.5C–1C charging. If your application needs a different rate window, we adjust cell selection and pack-level configuration rather than asking you to oversize capacity just to survive the current.

Size matching. In the same capacity class, 6S, 12S, 14S, 18S and 24S configurations produce significantly different pack lengths and heights. The dimensions in a standard product list are reference values for standard builds. In a custom project, however, we can re-engineer the internal arrangement around the actual space you have available.

Weight matching. For UAVs, eVTOL, AGVs and other weight-sensitive platforms, every gram affects endurance or payload. BECELL’s semi-solid cells reach 370 Wh/kg at cell level, and we support pack designs up to 800V. For a given capacity and series count, therefore, we can work toward your weight ceiling through cell selection and pack-level structural optimization.

Platform Coverage: 280–500 Wh/kg

The following parameters represent the capability range of the BECELL semi-solid platform. We confirm exact specifications for a custom project against your application requirements.

ParameterRange / Typical
Energy density tiers280 / 320 / 340–360 / 400 / 400–500 Wh/kg
Capacity coverage (Type/mAh)Approximately 10,000 mAh to 80,000 mAh class
Pack configurations6S / 12S / 14S / 18S / 24S (extendable)
Continuous discharge3C on most tiers; 2C on selected high-energy-density models
Burst discharge10C
Charging rate0.5C–1C
Cell-level benchmark370 Wh/kg semi-solid cells
Pack voltage capabilityUp to 800V pack design support

Important: The dimensions and weights in a standard product table are reference values for standard pack builds. In a custom project, we confirm the final envelope and mass against agreed mechanical interfaces and electrical specifications.

6S 30000mAh battery pack
6S 30000mAh battery pack

Three Entry Points Where Customization Changes the Outcome

Heavy-Duty UAVs and eVTOL

These platforms are sensitive to weight and burst current simultaneously. A 24S semi-solid pack with 3C continuous / 10C burst capability allows the pack to support takeoff, climb and maneuver power phases, while it retains energy efficiency during cruise. For example, BECELL has delivered a 24S 88.8V semi-solid pack for a large drone application, with 320 Wh/kg at cell level and 40Ah capacity. In custom UAV projects, the engineering focus is typically on pack compactness and matching the continuous/burst current window to the actual flight profile.

AGVs, Robotics and Specialized Electric Vehicles

Limited installation space and long continuous operating hours are common constraints. Higher-series configurations—14S, 18S and 24S—can reduce current for the same power level, and consequently they lower conductor losses and heat generation. In a custom project, we can re-lay out the internal series/parallel arrangement around the actual length, width and height of the battery bay, instead of forcing the chassis or compartment to accommodate a standard pack shape.

Applications with Rate Requirements Beyond Standard Offerings

The published 3C continuous / 10C burst figures are platform baselines. If your load profile requires a higher continuous rate, a longer burst duration, or a specific charging window, BECELL can address it through cell selection, electrode design and pack-level thermal management. In short, current is a design input, not a fixed ceiling.

How a Custom Program Runs

  1. Define the boundaries. Share target capacity or energy, continuous and burst current, installation envelope (L × W × H), weight ceiling, and operating voltage platform.
  2. Platform match and preliminary proposal. BECELL screens the 280–500 Wh/kg platform, proposes a pack configuration (6S–24S), and provides a preliminary envelope, mass estimate and rate check.
  3. Mechanical and electrical definition. Confirm interfaces, harness, connectors, BMS communication and thermal boundaries.
  4. Sample build and validation. Build samples to the agreed specification and validate them against your actual load profile.

We do not need a finished battery specification from you. Instead, we need the boundaries of your application. The earlier you define the current, size and weight constraints, the faster the proposal converges.

FAQ

What is the lowest energy density in the semi-solid platform?
The platform starts at 280 Wh/kg and covers the 280–500 Wh/kg range. If a project prioritizes cost or cycle life differently, you can select the appropriate tier within that range.

Are 3C continuous and 10C burst fixed values?
They are platform baselines. We review the exact continuous and burst rates for a project against your load profile. Selected high-energy-density tiers carry a 2C continuous rating.

Can I customize only the dimensions and keep the electrical specification standard?
Yes. Customization dimensions are independent. You can lock only the installation envelope, or you can adjust current, capacity, series count and weight together. BECELL matches the platform to the constraints you provide.

Can you build configurations outside 6S–24S?
The 6S–24S range represents standard pack references. We can discuss higher or special series counts during project evaluation. BECELL supports pack designs up to 800V.

How long does it take to receive a sample?
It depends on the depth of customization and platform matching. With complete current, size and weight boundaries, our engineering team typically provides preliminary feedback within a few business days. We schedule sample timing after specification confirmation.

Next Step: Send the Three Inputs

You do not need a complete battery specification to start. Send your continuous current, burst current, installation dimensions and weight ceiling—a paragraph, a sketch or a load profile is enough.

BECELL’s engineering team will assess the 280–500 Wh/kg semi-solid platform against your inputs, and then it will return a recommended tier, pack configuration, preliminary envelope and rate match.

Request a Custom Semi-Solid Battery Quote
Tell us: application type / target capacity or energy / continuous current / burst current / installation dimensions / weight ceiling / operating voltage.
Optional: upload a sketch, load profile or existing specification.

About BECELL
Huizhou Becell Technology Co., Ltd. is a battery manufacturer based in Huizhou, Guangdong, China, specializing in customized lithium battery packs and semi-solid-state battery solutions for demanding applications. BECELL semi-solid cells achieve 370 Wh/kg, and the company supports pack designs up to 800V. Custom development is available across current, size and weight requirements.

Store: www.becell0101.com

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top